Free in-home measure and quote - PGT, CGI and CWS impact lines compared on your actual openings, style by style
Sliding glass doors
Impact garage doorsPGTCGI
Before
After
Before
After
Before
AfterMarvin Door Installation in Wellington: What to Know First
Marvin door installation in Wellington typically runs $280 to $1,400 for labor on a standard door replacement, with full entry system installs landing between $2,500 and $7,800 depending on the door line and whether you’re dealing with impact-rated glass. Most Marvin door work we handle finishes in one to two days. Call (561) 349-4826 and we’ll give you a written line-item quote before any work starts.
This page is for Wellington homeowners who own a Marvin entry door, French door, or patio door and want it installed correctly by a crew that understands how these doors behave in South Florida humidity. We’re an independent service provider, not a factory-authorized dealer, which means we make parts decisions based on what actually lasts here, not what the sales catalog says. If your Marvin door is binding, leaking, or simply showing its age, you’re in the right place.
How Marvin Products Fail - and How We Fix Them
- Ultimate French doors pulling away from the jamb at the top corner. We see this on Marvin Ultimate swinging doors throughout Wellington, especially in homes built in the early 2000s. The cause is almost always hinge-side settlement combined with the weight of the door panel working against factory-installed screws that were never upgraded. We pull the door, sister the hinge mortises, and reset the panel with longer fasteners into the studs. The binding goes away and stays away.
- Marvin Integrity doors with a fogged or failed insulated glass unit. This is the most common Marvin door complaint in Palm Beach County, and it’s not a door problem, it’s a seal problem. The Integrity line uses a dual-pane glass package that can fail after ten to fifteen years of direct Wellington sun exposure. The symptom is condensation between the panes that never clears. We measure, order a matching IGU, and reseal the sash. You don’t replace the entire door for a failed glass pack.
- Ultimate Sliding French Door rollers grinding or dragging on the track. The tandem rollers on Marvin’s sliding doors pick up fine sand and shell grit from Wellington’s soil, and once the bearings wear they flatten out and the panel rides on the track itself. Left alone, that ruins the sill. We replace the roller cartridges with a heavier-rated assembly and clean the track channel properly, not just spray lubricant into it.
- Elevate and Signature doors with a warped or bowed panel after a wet season. Marvin’s fiberglass and wood-composite lines are stable products, but a door exposed to standing irrigation water or a poorly sloped threshold will absorb moisture and cup. The fix is correcting the water path first, then evaluating the panel. Sometimes a straightening can be done with shims and hinge adjustments. Sometimes the panel is done. We’ll tell you which before you spend a dollar.
- Marvin clad-wood entry doors with failing weatherstripping at the threshold. The factory kerf weatherstripping works for a few seasons, but Wellington’s heat cycles compress it, and once it’s flattened the door leaks air and water. We replace it with a denser compression bulb that matches Marvin’s kerf profile. It’s a fifteen-dollar part and about three times better than what the factory shipped.
Our Marvin Door Installation Process
- 1
Call and talk to a person. You’ll reach a live voice at (561) 349-4826, day or night. We ask what the door is doing, when it started, and whether it’s original to the house. We’ll set a time and show up when we say.
- 2
On-site measurement and diagnosis. Every opening gets measured twice. We check the jamb for plumb, the sill for level, and the hinge side for settlement. Then we walk you through what’s actually wrong and what it’ll take to fix it. Written quote, on paper, before you make a decision.
- 3
Parts decision: OEM or quality aftermarket. For warranty-sensitive work, we order Marvin OEM parts. For older doors where factory parts are backordered or discontinued, we’ll quote a quality aftermarket equivalent and explain exactly what changes. You decide with real information, not a sales pitch.
- 4
The install itself. Full removal, inspection of the rough opening, flashing and sealing at the sill, panel set, shimmed and fastened to spec, then adjusted for smooth operation. We don’t skip the flashing step, ever. That’s where Wellington door installs fail if they’re going to fail.
- 5
Operation test and air/water check. We cycle the door fifty times, check the reveal gaps, run water across the threshold, and make sure the lock engages without resistance. If it doesn’t pass, it’s not finished. That’s the Dale Kessler rule: if the pane is not true, the job is not done.
- 6
Cleanup and warranty registration. We register both warranty layers in writing before we leave your driveway, and you get a copy of everything. The Done Right Promise covers our workmanship, and we put that in writing too.
What Marvin Door Installation Costs in Wellington
Here’s what we typically quote on Marvin door work in the Wellington area:
- Labor-only installation for a standard Marvin entry door: $280-$520
- Labor for a Marvin French door pair: $520-$950
- Full replacement install including tearing out the old frame, new flashing, and re-trimming: $950-$2,200
- Impact-rated Marvin door with laminated glass, full system install: $2,500-$7,800 depending on size and whether it’s a single, double, or sliding configuration
- Glass-only replacement for a fogged Marvin IGU: $180-$420 per panel
- Threshold and weatherstripping rebuild on a leaking Marvin door: $140-$360
What moves the price: whether the rough opening needs correction, whether you’re upgrading to impact-rated glass, and whether the existing door was ever flashed correctly in the first place. Most homes in Wellington built before 2002 weren’t. Call (561) 349-4826 for an exact number. Estimates are free, and the number we quote is the number you pay.
Why Wellington Homeowners Call TruePane Windows & Doors for Marvin Work
We’ve been working in Palm Beach County since 2008, and Dale Kessler has been measuring, setting, and sealing doors here for nearly three decades. That matters on a Marvin job because these doors have specific tolerances, and a crew that treats them like any other pre-hung unit is going to leave you with a door that binds in August and leaks in September.
If a Marvin door needs parts we can’t get quickly, we can also show you comparable lines from Andersen, Pella, or PGT, side by side on paper, so you’re never stuck waiting on a backorder. We’re an authorized installer for more than a dozen manufacturers, which gives us options a Marvin-only shop doesn’t have. Every job carries the Done Right Promise, and a live person answers the phone 24/7, which matters when your door won’t close on a storm night. If it’s not right on the paperwork, it won’t be right on the wall. We put everything in writing before we start.
FAQs
Yes, as long as the installation follows Marvin’s published guidelines and the door itself isn’t modified in a way Marvin prohibits. We install to spec, use the correct flashing methods for South Florida, and provide documentation that supports any future warranty claim. Call (561) 349-4826 if you have a specific warranty concern and we’ll walk you through what’s covered.
Most single-door Marvin installations finish in one day, including removal of the old door, flashing work, and cleanup. A French door pair or an impact-rated replacement can take two days if the rough opening needs correction. We’ll give you a firm timeline in writing before we schedule, and we’ll be there when we say.
We use Marvin OEM parts whenever the door is under warranty or the part is available within a reasonable lead time. For older Marvin doors where factory parts are discontinued or backordered for months, we’ll quote a quality aftermarket equivalent and explain exactly what changes. You approve the part before we order it.
If the frame, hinges, and threshold are still solid, replacing just the insulated glass unit usually makes more sense than replacing the whole door. A fogged Marvin IGU runs $180 to $420 per panel installed in Wellington, versus $2,500 or more for a full new door. We’ll tell you honestly which way to go after we inspect the existing unit.
No. We quote in writing, and the number on the quote is the number on the bill. If we open up the wall and find hidden damage that needs addressing, we stop work and bring it to you with options before we spend another dollar. No surprise line items. That’s a square deal.
Written by Dale Kessler, Owner, TruePane Windows & Doors at TruePane Windows & Doors, serving Wellington and nearby areas.
Six Reasons Homeowners Choose TruePane Windows & Doors
Impact systems engineered to design pressures up to +/-100, matched to your wind zone - your openings hold when the storm arrives.
Low-E insulated impact glass from our manufacturer lines commonly cuts monthly cooling bills 20-30%.
Laminated impact glass shuts out up to 40% of outside noise - traffic, neighbors, weather.
Monitoring services run $30-90 a month. Laminated impact glass resists forced entry around the clock, with no subscription.
Florida homeowners average around 25% savings on the windstorm portion of their policy after protecting every opening - some homes qualify for more.
A full impact package upgrades curb appeal, buyer confidence and appraised value in one project.