Free in-home measure and quote - PGT, CGI and CWS impact lines compared on your actual openings, style by style
Mr-Glass Sliding & Patio Doors: The Wellington Owner’s Guide
We stock and install Mr-Glass-compatible sliding and patio door parts in Wellington, with most rollers, tracks, and handle sets running $165-$425 installed depending on the series and what failed. We carry common Mr-Glass hardware on the truck, so most jobs we complete in a single visit. The way most Wellington homeowners find us is simple: the door that used to glide with two fingers now needs a hip and a shoulder to move, and that tells them a roller has finally flattened or the track has worn through its anodized coating. Here’s what you need to know before you call.
Key Takeaways:
- We match Mr-Glass parts by series, track width, and wheel diameter - not guesswork from a photo
- OEM Mr-Glass hardware is what we recommend first; quality aftermarket equivalents exist for discontinued series
- Most Mr-Glass sliding door repairs in Wellington are done same-day for under $450
- We’re an independent service provider, not a Mr-Glass subsidiary - and we’ve been in Palm Beach County since 2008
Which Mr-Glass Models This Applies To
Mr-Glass produced several sliding door lines that ended up in Wellington homes, mostly built between 1998 and 2015. The common ones we see are the 7000 Series and 8000 Series sliders, plus a run of impact-rated patio doors installed in neighborhoods like Olympia, The Isles, and Buena Vida after the 2004-2005 hurricane seasons changed local building codes. Here’s the compatibility gotcha most people don’t know until a handyman guesses wrong: Mr-Glass changed their roller housing dimensions between the 7000 and 8000 Series, so a wheel that drops into one will bind in the other. The part numbers are not interchangeable, even though the doors look nearly identical from the outside. We measure the roller housing, the wheel diameter, and the track width with calipers before we ever order a part. On OEM versus aftermarket: we recommend OEM Mr-Glass hardware when the series is still supported, because the tolerances match what the door was built around. For discontinued Mr-Glass series, we use aftermarket equivalents from Prime-Line and Barton Kramer that we’ve tested in Florida humidity and salt air. If you email us a photo of the corner of the glass or the sticker on the door’s edge, we can usually identify the series from our records.
Signs Your Mr-Glass Sliding & Patio Door Is Failing
Owners in Wellington usually notice one of these five symptoms before the door actually stops moving. If you are seeing any of them, the fix is less expensive now than it will be after the door carves a groove in the track:
- The door needs force to move. A flattened roller wheel or a track packed with sand and grit from Wellington’s sandy soil. A healthy Mr-Glass slider glides with one hand. Needing two hands means the wheel is no longer round.
- It sounds like gravel when you slide it. The ball bearings inside the roller have worn or the stainless wheel has developed flat spots. That grinding sound is metal on metal, and it only gets worse.
- The door drops when you open it. The adjustable roller assembly has stripped or the screws backed out. The door now sits too low, and the bottom rail drags against the track frame.
- The lock or latch won’t engage. When the door rides low, the latch no longer lines up with the keeper in the jamb. It’s not a lock problem - it’s a door-height problem, created by the rollers.
- Condensation between the glass panes. A failed seal in the insulated glass unit, common on Mr-Glass patio doors that face full west sun in communities like Versailles or Saddle Trail Park. The rollers may still be fine, but the glass unit needs replacement.
Replacement Cost & What’s Included
Here’s the pricing picture for Mr-Glass sliding and patio door parts in Wellington, priced as installed. We quote parts and labor together so the number on the invoice matches the number we discussed before we started.
Typical installed prices in Wellington:
- Roller replacement (both panels, four roller assemblies): $185-$320
- Latch and handle set replacement: $95-$210
- Track replacement or resurfacing: $220-$400
- Full hardware refresh, rollers, track, handle, and weatherstripping: $390-$550
What drives the range: whether your door is an OEM-supported series, whether the track needs full replacement or just cleaning and adjustment, and whether dried silicone or stripped screws add removal time. Every job includes registration of both Mr-Glass hardware warranty layers in writing before we leave, plus our Done Right Promise. If it’s not done right, we make it right - no paperwork fight, no fine print.
DIY or Call Us?
The honest split is this: there are two things a Wellington homeowner can do before calling us, and one thing you should not attempt. You can clean the track with a vacuum and a nylon brush - that is safe and sometimes solves a door that just feels gritty. You can check that the screws holding the roller assemblies are snug. What you should not do is lift the door panel out of the track to swap rollers yourself. A sliding door panel weighs 120 to 200 pounds, and when it comes off its track, awkward happens fast. We’ve seen dropped panels that shattered in driveways in Royal Palm Beach and cracked tile in homes in The Landings. The panel does not go back in square by feel. That’s why we measure twice, set, and square. Call us at (561) 349-4826 and we can tell you over the phone whether you are looking at a DIY cleanup or a hardware replacement. We’ll be there when we say.
FAQs
Mr-Glass rollers in Wellington typically last 8 to 12 years, but doors that face west toward the Everglades or sit within a mile of the ocean can wear out in 5 to 7 years. Humidity accelerates bearing corrosion, and sandy soil loads the track with abrasive grit. We carry both original and aftermarket roller assemblies on the truck for most Mr-Glass series, so we can usually have your door rolling again the same day. Call (561) 349-4826 for an exact quote on your door.
No. Roller assemblies are sealed units; the bearings are not serviceable, and a flat-spotted wheel cannot be rounded. The track can often be cleaned and reused unless the anodized surface is worn through to bare aluminum, which is when we recommend track replacement. If you are not sure which condition your track is in, call (561) 349-4826 and we’ll check it while we’re there - the estimate is free.
Most Mr-Glass roller and hardware replacements in Wellington are completed in one visit, usually 45 to 90 minutes. That includes removing the panels, swapping the hardware, resetting the door height, adjusting the square, and testing the latch. If the track requires replacement, we may need to order the extrusion and return for a second visit. Call (561) 349-4826 and we’ll give you a straight time frame based on your door’s series.
We stock the most common Mr-Glass roller assemblies, handle sets, and weatherstripping on the truck, and our Wellington warehouse keeps additional Mr-Glass-compatible inventory. For some discontinued series, we source parts from our network of Florida suppliers and typically have them within two to three business days. We also stock parts for PGT, CGI, and CWS sliding doors. If you are not sure which series you have, call (561) 349-4826 and we’ll help you identify it over the phone.
Get Your Mr-Glass Door Sliding Right Again
If your Mr-Glass sliding or patio door is stiff, noisy, or dropping in the track, call us at (561) 349-4826 for a free estimate. We’ll identify the series, quote OEM and aftermarket options side by side on paper, and register both warranty layers before our truck leaves your driveway. We’ve been working in Wellington homes for over four decades, and if the pane is not true, the job is not done.
Written by Dale Kessler, Owner, TruePane Windows & Doors, serving Wellington and nearby areas.
Six Reasons Homeowners Choose TruePane Windows & Doors
Impact systems engineered to design pressures up to +/-100, matched to your wind zone - your openings hold when the storm arrives.
Low-E insulated impact glass from our manufacturer lines commonly cuts monthly cooling bills 20-30%.
Laminated impact glass shuts out up to 40% of outside noise - traffic, neighbors, weather.
Monitoring services run $30-90 a month. Laminated impact glass resists forced entry around the clock, with no subscription.
Florida homeowners average around 25% savings on the windstorm portion of their policy after protecting every opening - some homes qualify for more.
A full impact package upgrades curb appeal, buyer confidence and appraised value in one project.



Before
After
Before
After
Before
After